机械设计名词术语(5)
关键字:机械设计 | |
绿色设计 green design ; design for environment 马耳他机构 Geneva wheel ; Geneva gear 马耳他十字 Maltese cross 脉动无级变速 pulsating stepless speed changes 脉动循环应力 fluctuating circulating stress 脉动载荷 fluctuating load 铆钉 rivet 迷宫密封 labyrinth seal 密封 seal 密封带 seal belt 密封胶 seal gum 密封元件 potted component 密封装置 sealing arrangement 面对面安装 face-to-face arrangement 面向产品生命周期设计 design for product`s life cycle, DPLC 名义应力、公称应力 nominal stress 模块化设计 modular design, MD 模块式传动系统 modular system 模幅箱 morphology box 模糊集 fuzzy set 模糊评价 fuzzy evaluation 模数 module 摩擦 friction 摩擦角 friction angle 摩擦力 friction force 摩擦学设计 tribology design, TD 摩擦阻力 frictional resistance 摩擦力矩 friction moment 摩擦系数 coefficient of friction 摩擦圆 friction circle 磨损 abrasion ;wear; scratching 末端执行器 end-effector 目标函数 objective function 耐腐蚀性 corrosion resistance 耐磨性 wear resistance 挠性机构 mechanism with flexible elements 挠性转子 flexible rotor 内齿轮 internal gear 内齿圈 ring gear 内力 internal force 内圈 inner ring 能量 energy 能量指示图 viscosity 逆时针 counterclockwise (or anticlockwise) 啮出 engaging-out 啮合 engagement, mesh, gearing 啮合点 contact points 啮合角 working pressure angle 啮合线 line of action 啮合线长度 length of line of action 啮入 engaging-in 牛头刨床 shaper 凝固点 freezing point; solidifying point 扭转应力 torsion stress 扭矩 moment of torque 扭簧 helical torsion spring 诺模图 Nomogram O 形密封圈密封 O ring seal 盘形凸轮 disk cam 盘形转子 disk-like rotor 抛物线运动 parabolic motion 疲劳极限 fatigue limit 疲劳强度 fatigue strength 偏置式 offset 偏 ( 心 ) 距 offset distance 偏心率 eccentricity ratio 偏心质量 eccentric mass 偏距圆 offset circle 偏心盘 eccentric 偏置滚子从动件 offset roller follower 偏置尖底从动件 offset knife-edge follower 偏置曲柄滑块机构 offset slider-crank mechanism 拼接 matching 评价与决策 evaluation and decision 频率 frequency 平带 flat belt 平带传动 flat belt driving 平底从动件 flat-face follower 平底宽度 face width 平分线 bisector 平均应力 average stress 平均中径 mean screw diameter 平均速度 average velocity 平衡 balance 平衡机 balancing machine 平衡品质 balancing quality 平衡平面 correcting plane 平衡质量 balancing mass 平衡重 counterweight 平衡转速 balancing speed 平面副 planar pair, flat pair 平面机构 planar mechanism 平面运动副 planar kinematic pair 平面连杆机构 planar linkage 平面凸轮 planar cam 平面凸轮机构 planar cam mechanism 平面轴斜齿轮 parallel helical gears 普通平键 parallel key 其他常用机构 other mechanism in common use 起动阶段 starting period 启动力矩 starting torque 气动机构 pneumatic mechanism 奇异位置 singular position 起始啮合点 initial contact , beginning of contact 气体轴承 gas bearing 千斤顶 jack 嵌入键 sunk key 强迫振动 forced vibration 切齿深度 depth of cut 曲柄 crank 曲柄存在条件 Grashoff`s law 曲柄导杆机构 crank shaper (guide-bar) mechanism 曲柄滑块机构 slider-crank (or crank-slider) mechanism 曲柄摇杆机构 crank-rocker mechanism 曲齿锥齿轮 spiral bevel gear 曲率 curvature 曲率半径 radius of curvature 曲面从动件 curved-shoe follower 曲线拼接 curve matching 曲线运动 curvilinear motion 曲轴 crank shaft 驱动力 driving force 驱动力矩 driving moment (torque) 全齿高 whole depth 权重集 weight sets 球 ball 球面滚子 convex roller 球轴承 ball bearing 球面副 spheric pair 球面渐开线 spherical involute 球面运动 spherical motion 球销副 sphere-pin pair |